-250x250.jpg)
-250x250.png)
JL AUDIO C1-690
JL AUDIO C1-690
2-Way Component System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications.
Surface and flush mounts are included with C1 tweeters for maximum installation versatility.
C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design.
This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound.
At the core of the C1-690 is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system.
A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing.
These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, 1-inch aluminum dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition.
The tweeter’s design has inherently excellent off-axis response and high-frequency extension.
It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit.
An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling.
When it comes to value, C1 is the real deal!
Sold as a pair. Grilles not available.
C1-690 SPECIFICATIONS:
Continuous Power Handling: 60 Watts
Recommended Amp Power: 10-100 Watts per channel (RMS)
Efficiency: 91.5 dB @ 1W / 1m | 97.5 dB @ 1W / 0.5m
Sensitivity: 94.0 dB @ 2.83V / 1m
Nominal Impedance: 4 ohm
Frequency Response: 39Hz - 22 KHz ± 3 dB
Woofer:
Injection-molded, mineral-filled, polypropylene cone
Rubber, positive roll surround
1.2 in. (30 mm) diameter voice coil
Flat, Conex® spider with integrated lead wires
Ferrite Magnet
Tweeter:
Edge-driven, silk-suspended aluminum dome
1.0 in. (25 mm) diameter diaphragm / voice coil
Ferrofluid cooling / damping
Neodymium magnet
Crossover:
Natural roll-off, low-pass
2nd order, high-pass filter with inductor and
electrolytic capacitor
Included Components and Parts:
• Two (2) C1-690cw 6 x 9-inch (150 x 230 mm) woofers
• Two (2) C1-100ct 1.0-inch (25 mm) tweeters
• Two (2) surface-mount tweeter fixtures
• Two (2) C1-100cthp in-line, high-pass filters on 4 ft. (1.2 m) wire harnesses
• Two (2) metal spring clips (for tweeter flush-mounting)
• Eight (8) #8 x 1.50-inch (38mm) sheet metal screws
• Four (4) #6 x .625-inch (22 mm) sheet metal screws
• Eight (8) mounting clips
• Two (2) 4.7 mm female crimpable connectors
• Two (2) 2.8 mm female crimpable connectors
• Two (2) 10mm stud bolts with fixed M4 nut
• Two (2) 25mm stud bolts with fixed M4 nut
• Two (2) M5 nuts
• Two (2) bottom-mount spacer adaptor rings